在線留言|
您好，歡迎來到 濟南萬中電動扳手有限公司網站！
服務熱線： 400-117-8816
13406879330
13406879330
扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家
扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家
1.高速馬達、低噪音、大功率、額定電壓220V50/60Hz；
1. High speed motor, low noise, high power, rated voltage 220V50 / 60Hz;
2.緣工程材料機殼、雙重緣、安堅固可靠；
2. High quality engineering material shell, double edge, secure and reliable;
3.槍式握把、負荷人體工學、增加握持力、減輕疲勞強度；
3. Gun grip, load ergonomics, increase grip strength and reduce fatigue strength;
5.精密行星減速、功效提高、運行平穩；
5. Precise planetary deceleration, improved efficiency and stable operation;
2、工具使用的環境溫度為-10℃-40℃，過高過低都會影響控制精度。
2. The environmental temperature of the tool is - 10 ℃ - 40 ℃, too high or too low will affect the control accuracy.
3、被擰螺栓的初始扭矩不得大于工具的額定扭矩的70%。螺栓達到額定扭矩后不得重?cái)Q。
3. The initial torque of the screwed bolt shall not be greater than 70% of the rated torque of the tool. The bolts shall not be re tightened after reaching the rated torque.
4、工具用于拆卸螺栓時，其扭矩不得大于額定扭矩值。一般情況下，不是本扳手?jǐn)Q緊的或銹蝕嚴重的螺栓，不宜用本扳手拆卸，以免造成工具損壞。
4. When the tool is used to remove the bolt, its torque shall not be greater than the rated torque value. Generally, bolts that are not tightened or seriously rusted by this wrench should not be removed by this wrench to avoid tool damage.
5、變換旋轉方向時，必須待電機停止轉動后進行，嚴禁在運轉中撥動正反開關。
5. When changing the direction of rotation, it must be carried out after the motor stops rotating. It is strictly forbidden to move the positive and negative switches during operation.
6、當扳手自動停止后即可松開開關（如果不斷開開關，過5秒鐘扳手就會自行啟動）待4-5秒后再進行開動扳手，否則扳手不能啟動。
6. When the wrench stops automatically, the switch can be released (if the switch is opened continuously, the wrench will start automatically after 5 seconds) and the wrench can be started after 4-5 seconds, otherwise the wrench cannot be started.
