1. 一般情況下，選用II類手持式電動機，安裝漏電保護器，額定沖擊動作電流不大于15mA，額定動作時間小于0.1秒。如果使用I類手提電動工具，也必須是零保護。操作人員必須戴絕緣手套、穿絕緣靴或站在絕緣墊上。
1. Generally, type II hand-held motor is selected and leakage protector is installed. The rated impulse action current is not more than 1, and the rated action time is less than 0.1 seconds. If you use Class I safe hand-held electric tools, it must also be zero protection. Operators must wear insulating gloves, insulating boots or stand on insulating pads.
2. 在潮濕的地方或金屬框架上操作時，必須選擇II類手持電動工具，并且必須安裝防濺泄漏保護器。嚴禁使用I類手提電動工具。
2. When operating in wet places or on metal frames, Class II safe hand-held electric tools must be selected and anti-splash and leakage protectors must be installed. It is strictly forbidden to use Class I safe hand-held electric tools.
3.在狹窄的地方(鍋爐、金屬容器、溝槽、管道等)，宜使用帶隔離變壓器的III類手持電動工具;II類手提電動工具必須配備防濺裝置。在狹窄處安裝隔離變壓器或漏電保護器。
3. In narrow places (boilers, metal containers, grooves, pipes, etc.), Class III hand-held power tools with isolation transformers should be used; Class II hand-held power tools must be equipped with anti-splash devices. Install isolation transformer or leakage protector in narrow area.
扭剪扳手
Torsion wrench
4、手持電動工具的載重線必須是耐候橡膠護套銅電纜，且無接頭。禁止使用塑料紗線。
4. The load line of hand-held electric tools must be weatherproof rubber sheathed copper cable without joint. Plastic yarns are prohibited.
5. 砂輪接觸濕氣、變形、裂紋、斷裂、切邊或接觸油、堿等，不得使用。受濕氣影響的砂輪葉片不能自行干燥。砂輪與接頭軟墊應安裝牢固，螺母不宜過緊。
5. The grinding wheel shall not be used when it is in contact with moisture, deformation, crack, fracture, trimming or oil or alkali. Wheel blades affected by moisture cannot be dried by themselves. Grinding wheel and joint cushion should be firmly installed, nuts should not be too tight.
6. 操作前檢查:
6. Check before operation:
(1)外殼、手柄無裂紋、損壞;
(1) There are no cracks or damages in the shell and handle;
(2)保護零位接線正確、牢固、可靠，電纜線、插頭完好，開關運行正常，注意開關的操作方法;
(2) Protect correct, firm and reliable zero-position wiring, intact cable and plug, normal operation of switch, pay attention to the operation method of switch;
(3)電氣保護裝置良好可靠，機械保護裝置齊全。
(3) The electrical protection device is good and reliable, and the mechanical protection device is complete.
7. 開機后空操作，檢查工具操作應靈活、暢通。
7. Flexibility and smoothness should be ensured in the operation of check tools after boot-up.
8、手持式電動工具(電動扳手)，操作時增加的力要平衡，不要太用力。
8. Hand-held electric tools (electric wrenches) should balance the increased force during operation and not exert too much force.
9. 嚴禁超載。請隨時注意音響及溫升。
9. No overloading. Please pay attention to the sound and temperature rise at any time.
10. 操作中不得觸摸電動工具(電動扳手)。
10. Electric tools (electric wrenches) should not be touched in operation.
機器運行時不要停止。
Do not stop when the machine is running.
使用電動工具(電動扳手)注意事項;
Cautions for using electric tools (electric wrenches);
(1)扳手頭應推在工件上，不得空打空推;
(1) The wrench head shall be pushed on the workpiece and shall not be pushed empty;
(2)工件上必須垂直支撐，不要讓螺栓晃動;
(2) The workpiece must be supported vertically and the bolts should not be shaken.
(3)使用大扭矩電動工具(電動扳手)，作業現場應圍繞護欄設置。地面應有堅實的作業平臺。
(3) With large torque electric tool (electric wrench), the operation site should be set around guardrail. The ground should have a solid operating platform.
以上是
扭剪扳手制造商為大家整理的相關內容，想以了解更多內容，歡迎訪問網站：http://m.cnbeilibao.com
The above is the relevant content of the wrench manufacturer for you. For more information, please visit the website: http://m.cnbeilibao.com.
